We recommend that you use a flight case, so as to give your power mixer optimum protection during use or transport. Always use the original packing carton to prevent damage during storage or transport.
Make sure that children cannot play unsupervised with the device or its packaging. Blown fuses must be replaced by fuses of the same type and rating! The mains connection is made using the enclosed power cord and a standard IEC receptacle. It meets all of the international safety certification requirements.
Please make sure that all units have a proper ground connection. For your own safety, never remove or disable the ground conductor from the unit or on the AC power cord. The sound quality may diminish within the range of powerful broadcasting stations and high-frequency sources. Increase the distance between the transmitter and the device and use shielded cables for all connections. To arrange for warranty service, please contact the retailer from whom the equipment was purchased.
Should your country not be listed, please contact the distributor nearest you. A list of distributors can be found in the support area of our website www. Registering your purchase and equipment with us helps us process your repair claims quicker and more efficiently.
This manual is designed to give you both an overview of all control elements and to provide details about how to use them. To provide you with a clear structure, we have grouped the control elements according to their function. They can easily be found on the enclosed numbered illustrations. If you need more detailed information on specific topics, please visit our web site at www. A detailed description of all functions of your power mixer can be found in the following chapters. Please also refer to the enclosed sheet with the numbered illustrations to get a good overview of the control layout.
Use the TRIM control to adjust the input gain. Be sure to set this control fully counter-clockwise before you connect or disconnect a signal source to an input. The mono channels are equipped with a high-slope LOW CUT filter eliminating unwanted low-frequency signals like rumble noise. Use the MID control to boost or cut the midrange frequencies.
The stereo channels contain a stereo EQ section. The cutoff frequencies of the high and low bands are 12 kHz and 80 Hz respectively, while the center frequencies of the high-mid and low-mid bands are 3 kHz and Hz respectively.
The FX control determines the signal level sent from each channel to the built-in effects processor; this signal is also present at the FX SEND jack see. Accordingly, the PMP also has two effect aux buses, which have one output jack in common see and.
It determines the relative volume of the left and right input signals before they are routed to the stereo main output. The MUTE switch mutes the channel in the main mix. The pre-fader signals monitor buses remain operative. Be sure to switch off your audio system before you activate the phantom power supply to protect your monitor speakers from switch-on thumps. Please remember to use either the microphone or the line input on a specific channel. Never use both at the same time!
When you connect a mono line signal to a stereo channel, always use the left input. The mono signal will then be reproduced by both sides equally. Insert points or simply inserts are used to process a signal with dynamic processors or equalizers. Unlike reverb and other effects, which are usually added to the dry signal, dynamic processors usually process the entire signal. So, aux send buses are not the best solution. Dynamic processors need to be inserted directly into the signal path.
Once processed, the signal then returns to the mixing console at the same point where it left. All mono input channels are equipped with inserts.
The signal will then be reproduced on both sides. Like the other channels, they also feature a PFL switch. The phantom power supply provides the voltage necessary for the operation of condenser microphones. In most cases, dynamic microphones can still be used, as long as they are connected in a balanced configuration.
If in doubt, please contact the manufacturer of your microphone! After switching on, please allow the system to stabilize for about one minute, before you adjust the input gain. Never use unbalanced XLR connectors pins 1 and 3 interconnected on the MIC input jacks, if you are going to use the phantom power supply. Please read the information given on the rear panel of the power mixer. Information on how to properly connect your speaker with regard to polarity can be found on the rear of the unit PIN assignment see also and.
If the speakers have a limited frequency response in the bass range, this function allows you to filter this range at the output signal of the mixer and thus adapt it optimally to the frequency response of the speakers. During pauses you can prevent the microphones from picking up noise or interference, which would then be reproduced by the P.
There is also no need to move the faders and lose your mix. Your power mixer features a graphic 7-band equalizer, which allows you to fine-tune the sound depending on the room acoustics. In the center position the frequency response is not effected. To boost or cut a certain frequency range, simply move the corresponding fader upward or downward respectively. All other LEDs will be darker. Now, cut the frequency range in question until feedback disappears the LED gets darker or goes out.
This function is available for both the main and monitor mix. When not pressed, the stereo equalizer processes only the main mix. When the switch is pressed, the EQ processes only the monitor mix. Press the EQ IN switch to activate the equalizer. Use this LED display to control the output level of the main signal. Welcome to ManualMachine. We have sent a verification link to to complete your registration. The Speakon connector was especially developed for high-power loudspeakers.
Full Screen Viewing — to easily view the user manual without downloading it to your computeryou can use full-screen viewing mode. Helpful 0 Not Helpful Comment Flag. Usual problem is the Channel A amplifier has burned and blown the switching transistors. When PFL is on, the corres- be found in the following chapters.
Please make sure that all units have a proper ground connection. Standard set-up example main and the monitor signals, separately from each another. Summary of the content on the page No. Not finding what you are looking for? Run the speaker leads through the handles of the speakers to prevent inadvertent unplugging due to personell tripping over cables.
What is the cause? I will be using it with some mics at a function in an hotel. I only want 2 speakers to run on this because I have a limited space. Behringer Xenyx fx Mixer I have some diagrams and stuff, so if you need some sing out.
The Knight Level 3 Expert Answers. To prevent damage to the mixer, make sure all speaker leads are secure before powering the system. The A side power amp is used to drive monitor speakers and the B side the mains. Usually an internal board arc occurs and unless very skilled at board work of clearing behrjnger burned area and replacing the components you are better to replace the HCA amplifier module Please enter a valid email address. For your own safety, never remove or disable the ground conductor from the unit or of the AC power cord.
Use TRS interconnects to yout effects unit. If however you are ok with electronics you can have a go yourself, manuals are few and very far between. Login to post Please use English characters only. Posted by SangTran on Jul 15, Many people prefer to read the documents not on the screen, but in the printed version.
DO NOT put mono plugs pkp these. Blown fuses must be replaced by fuses of the same type and rating. Your answer needs to include more details to help people. Can you please specify what cables are required including the length of the speaker cables as I only know the very basic. I have freestanding Series 8 dishwasher.
0コメント